The RUTX11 has been a workhorse for sites that need more than a basic 4G router: gigabit ports, dual SIM, and often a fixed line on the WAN port with mobile as the backup. That last arrangement is where ping reboot gets misconfigured, because the router can test the wrong connection without anyone noticing.
RUTX11 ping reboot at a glance
| Router | Teltonika RUTX11, industrial LTE Advanced router |
| Ports | 4 x Gigabit Ethernet, WiFi, Bluetooth, GPS |
| SIM | Dual SIM |
| Where | System, Maintenance, Auto Reboot, Ping/Wget Reboot |
| First action | Restart mobile connection |
| Biggest trap | Pinging through the fixed WAN instead of the mobile link |
Teltonika lists the RUTX11 as end of life. There are a lot of them still in service, which is why this guide exists, but for new installs check Teltonika’s current range. The ping reboot settings below carry straight over to current RutOS models.
Ping reboot on a dual-WAN site
When a RUTX11 has a fixed line on its WAN port, the main WAN is usually the fixed line and the mobile connection sits waiting as backup. A ping reboot rule left on its default interface tests the main WAN. The fixed line answers happily, the rule reports healthy, and nobody finds out the mobile backup has been dead for weeks until the day it is needed.
If the rule is there to protect the mobile connection, set its interface to ping from mobile. Use the router’s failover health checks, not a reboot rule, to decide when to switch from the fixed line to mobile.
Configuring ping reboot on the RUTX11
Everything below is on current RutOS 7 firmware. The menu names come from Teltonika’s own RUTX11 documentation. Older firmware put the same feature under Services, Auto Reboot, and called some fields by different names, so update the firmware first if what you see does not match.
- Test the target by hand. Before you touch the rule, ping the address you plan to use from the router’s diagnostics page. If it does not answer there, it will not answer for ping reboot either.
- Open the rule. Go to System, Maintenance, Auto Reboot. The Ping/Wget Reboot section has one rule already filled in, switched off. Click the pencil icon to edit it.
- Choose the check. Set Type to Ping.
- Choose the action. Set Action if no echo is received to Restart mobile connection. It drops and re-establishes the data session without taking the whole router down. Modem reboot and Device reboot are heavier options for a second rule.
- Set the timing. Interval 5 minutes, Timeout 5 seconds, Interval count 2. Interval count is the number of extra attempts after the first one, so 2 means the router acts after three consecutive failures, about 15 minutes of failed checks.
- Set the hosts. For an internet SIM, use two addresses from different operators, such as
8.8.8.8and9.9.9.9, and set Action condition to When all requests fail. On a closed private APN, use an address inside the APN instead. - Save and test. Save and apply, then prove it works: point the rule at an address you know will not answer, wait for the action, check the event log, and put the real target back.
The RUTX11 has two SIM slots, so the rule shows a host field for each SIM: Host to ping from SIM 1 and Host to ping from SIM 2. Set both. If the two SIMs are on different network types, for example one internet SIM and one private APN SIM, each needs a target that SIM can actually reach. The router only acts when all the hosts defined for the active SIM fail to reply.
Interface matters on the RUTX11, because it can take a wired WAN as well as mobile. Left on Automatically selected, the pings go out through whichever interface is currently the main WAN. If the fixed line is primary, you are testing the fixed line, not the 4G or 5G backup. Set Ping from mobile when the rule is there to protect the mobile connection.
The settings I start with
| Type | Ping |
| Action if no echo is received | Restart mobile connection |
| Interval | 5 minutes |
| Timeout | 5 seconds |
| Interval count | 2 (three failures in total) |
| Action condition | When all requests fail |
| Host to ping | 8.8.8.8 and 9.9.9.9 on an internet SIM, an address inside the APN on a private one |
| Interface | Ping from mobile |
Then add a second rule with a longer interval, 30 minutes for example, and the action set to Device reboot. If restarting the mobile connection has not cleared the fault, the heavier action gets a turn. The settings builder works these values out for your SIM type, and the recovery and reboot loop calculator shows how long a stalled link stays down with them.
Two settings people miss
No action on data limit. If you use RutOS mobile data limits, switch this on. Without it, a SIM that has hit its cap fails every ping, and the router restarts the connection over and over while nothing can possibly get through.
Send SMS. The action list includes Send SMS instead of a restart. On a site where an unexpected restart would do damage, an SMS alert is a sensible first rule, with the restart as a second rule further out.
Troubleshooting
It reboots every few minutes
Nearly always the target. A public address on a private APN can never answer, so every check fails and the router cycles. I explain why in the ping reboot cycle of death and what to use instead in Ping Reboot on Private IP SIM Cards.
It never acts, even when the link is clearly dead
Check the rule is switched on, that the host is set for the SIM that is actually active, and that Interface is pinging the path you think it is. On a dual-WAN site, a healthy fixed line will keep answering the pings while the mobile backup is dead.
It acts, but the link does not come back
Then a restart is not the fix. A barred SIM, a data cap, wrong APN settings or a roaming SIM stuck on a network that will not pass data all look like a dead link, and none of them are cured by rebooting. See roaming SIMs that get stuck.
For the other recovery features in RutOS, such as the reboot scheduler, SMS reboot and the hardware watchdog, see Teltonika Router Auto-Reboot and Resilience Features.
Questions
Where is ping reboot on the RUTX11?
On RutOS 7 it is under System, Maintenance, Auto Reboot, in the Ping/Wget Reboot section. There is one rule already filled in with 8.8.8.8, switched off by default.
What does Interval count mean on the RUTX11?
It is the number of extra attempts after the first failed one. With Interval count 2, the router acts after three consecutive failures.
Should the RUTX11 restart the connection or reboot?
Restart mobile connection first. It is quicker and keeps the router up. Add a second rule with a longer interval that does a full Device reboot if the restart did not fix it.
Do I need separate ping hosts for each SIM on the RUTX11?
Yes, set Host to ping from SIM 1 and from SIM 2. Each must be reachable from that SIM, which matters if one SIM is on a private APN.